Has my shaft been tipped? Shaft Measurements from raw tip to graphics

[Richsgbox]

Tour AD- XC 7x anyone?

[jholiday]

Does anyone know if these measurements (specifically with the AD DI 7s) are with the adapter on? Someone’s selling me ad di 7s that measures 24 1/4 to the first green ring from the very end of the TaylorMade adapter. I know the adapter gives an extra 3/8 of an inch. 

Edited November 11, 2021 by jholiday

[ChitownM2]

1 hour ago, jholiday said:

Does anyone know if these measurements (specifically with the AD DI 7s) are with the adapter on? Someone’s selling me ad di 7s that measures 24 1/4 to the first green ring from the very end of the TaylorMade adapter. I know the adapter gives an extra 3/8 of an inch. 

 

They should be to the tip of the raw shaft (hopefully).  Otherwise, all of the measurements would be worthless since every brand of adapter is slightly different in the length it adds....

[geochitown]

The dimensions in this thread and most on this site refer to the tip of the shaft to the reference graphic on said shaft (not the tip of the adapter).

 

That's why it's especially good when people include photos of the shafts alongside a ruler.

[rynobucket]

Anybody have a tip-to-graphics measurement for an Aldila Rogue White 130msi?

Thanks

[geochitown]

I’m pretty sure that this Rogue White 130 is untipped

 

19-1/4” from the tip of the shaft to the top of the Atomic A

 

 

Edited November 18, 2021 by geochitown
Added 2nd photo

[Dougy]

looking for info on aerotech steelfiber iron shaft .370 parallel if its been tipped fc 90 f4 , or i95 S

need measurement from tip end to first set of rings on uncut shaft or a true measurement from end rings any # shaft

[geochitown]

Best to contact aerotech cs 

 

they are very responsive in my experience 

[Nihonsei75]

On 10/19/2021 at 12:19 PM, Richsgbox said:

Tour AD- XC 7x anyone?

Did you get a dm on that? I'm anticipating an XC 6s SS 1" from TM.

[Richsgbox]

16 hours ago, Nihonsei75 said:

Did you get a dm on that? I'm anticipating an XC 6s SS 1" from TM.

No responses. I did find a new untipped for reference. Not 100 but I wanna say it was 4 inches to the graphic. 

[rbpwrx]

Need untipped dims on Tensei CK PRO (Blue, but probably all the same) from tip to bottom of (blue) ring, HYBRID shaft (I'm assuming it 42" raw). THANKS!

[geochitown]

I found this on another thread

 

The tip to graphic measurement to the "I" in Tensei is 17 1/2" for Pro Blue Hybrid

[bahngooman]

Going to be a suuuper long shot…but what are the chance someone has measurements for aldila rip phenom 50 shafts? Looking for reg and stiff in particular 🤞😅

[Stuart_G]

8 hours ago, bahngooman said:

Going to be a suuuper long shot…but what are the chance someone has measurements for aldila rip phenom 50 shafts? Looking for reg and stiff in particular 🤞😅

 

I have a phenom 60 stiff I can measure when I get home from work - and aldila is normally pretty consistent across different weights.   But a better idea would be just contact Aldila CS directly - call or email.  They are usually pretty accommodating to those types of questions.  Or at least they always have been in the past.

Edited May 10, 2022 by Stuart_G

[bahngooman]

3 hours ago, Stuart_G said:

 

I have a phenom 60 stiff I can measure when I get home from work - and aldila is normally pretty consistent across different weights.   But a better idea would be just contact Aldila CS directly - call or email.  They are usually pretty accommodating to those types of questions.  Or at least they always have been in the past.

Thanks! I’ll reach out to CS too, hopefully they respond considering the age of this shaft 😂🤞

[geochitown]

Found this one in a post and verified

 

Matrix RUL 60 (gold shaft)

 

19.5” from tip of shaft to the “x” in “flex” for an Un-tipped shaft

Edited August 7, 2022 by geochitown

[rbpwrx]

From above: "Diamana Ahina. 18-3/16" tip to "N" in Rayon"

Not sure if this is wood or hybrid shaft. Looking for hybrid.

Thanks!

[geochitown]

4 hours ago, rbpwrx said:

From above: "Diamana Ahina. 18-3/16" tip to "N" in Rayon"

Not sure if this is wood or hybrid shaft. Looking for hybrid.

Thanks!

I’m sure that’s for  the wood shaft.

can’t help with the hybrid

[AUS_backintheswing]

Does anyone know a tip to graphics measurement  for an uncut KBS TD 60 and 70 category 3?

[jmkorting]

Is there any information on how to tell tipping on a Speeder NX shaft?  I didn't find anyone on this thread posted info for this particular shaft.

[jmkorting]

In case anyone is interested - Speeder NX is, "14.75 inches to the first visible graphic on the cosmetic."  This is from Chad @Fujikura Golf

[Scotty_gilbert]

Hi, I see the Kai’li blueboard 70s in the list, but can anyone confirm if the 70X has the same measurement?

I’ve tried @MITSUBISHI CHEMICAL via their website but no news yet. 
 

thanks in advance, Scott  🙂 

[MITSUBISHI CHEMICAL]

On 10/7/2022 at 12:24 AM, Scotty_gilbert said:

Hi, I see the Kai’li blueboard 70s in the list, but can anyone confirm if the 70X has the same measurement?

I’ve tried @MITSUBISHI CHEMICAL via their website but no news yet. 
 

thanks in advance, Scott  🙂 

sorry for our delay! admin (me) has been traveling! To answer your question, graphic start position for 70X KB should be identical to 70S.

[Skipperation]

@MITSUBISHI CHEMICAL Any help with a measurement for the slightly older grey Diamana D+/S+ hybrid shafts? I have a D+ 100 HY that I'm trying to find some details on.

Cheers

Edited October 12, 2022 by Skipperation

[BUDDA CRISP]

Graphite Design Tour AD DI 7x black with the new cosmetics is 24.75 inches from tip to first ring. The old cosmetics version is 25.75 inches. 

Edited October 13, 2022 by BUDDA CRISP

[Scotty_gilbert]

On 10/11/2022 at 3:44 PM, MITSUBISHI CHEMICAL said:

sorry for our delay! admin (me) has been traveling! To answer your question, graphic start position for 70X KB should be identical to 70S.

Hey, no apology necessary - we’re all busy! 
Thanks for the info, off to check it now!

cheers, Scott 

[jmkorting]

Anyone have information on how to tell how much a VA Composites shaft has been tipped?  Particularly the VA Raijin hybrid shaft.  Thanks in advance. 

[geochitown]

On 10/12/2022 at 10:02 AM, Skipperation said:

@MITSUBISHI CHEMICAL Any help with a measurement for the slightly older grey Diamana D+/S+ hybrid shafts? I have a D+ 100 HY that I'm trying to find some details on.

Cheers

i just measured a D+ 90 hybrid shaft and it was 16.25” from tip to the n in rayon.

 

 The raw shaft measures 39.5” so it’s already been trimmed, so I don’t know if the shaft was untipped or not 

 

[third-times-a-charm]

Aldila 2kxv hybrids

4 7/8” to the T In MLT

[wobgon]

The original post says to the first gold ring on a kiyoshi gold 65....I am trying to find the gold ring...Any help?